Search found 645 matches

by jph
Tue Jun 15, 2021 7:33 am
Forum: Arduino
Topic: Arduino Uno not connecting
Replies: 20
Views: 190

Re: Arduino Uno not connecting

If hw_connected() returns true then the device is connected. So yes it can be used to check the connection. Please define a 'device' in relation to a complete board connection ? (as opposed to looking at individual ancillary connections to the device). That would be informative. Device is irrelevan...
by jph
Mon Jun 14, 2021 10:24 am
Forum: Arduino
Topic: Arduino Uno not connecting
Replies: 20
Views: 190

Re: Arduino Uno not connecting


If hw_connected() returns true then the device is connected. So yes it can be used to check the connection.
Please define a 'device' in relation to a complete board connection ? (as opposed to looking at individual ancillary connections to the device). That would be informative.
by jph
Mon Jun 14, 2021 9:16 am
Forum: Arduino
Topic: Arduino Uno not connecting
Replies: 20
Views: 190

Re: Arduino Uno not connecting

JohnF John, you can adjust the 'int interval = value to virtually anything you want to simulate the update of your code TX NOT THE TICK() For example, the same code based on the above but with a 50mS update for data without effecting tick() Works fine - Forget that it signs on as Leonardo - that bi...
by jph
Mon Jun 14, 2021 9:09 am
Forum: Arduino
Topic: Arduino Uno not connecting
Replies: 20
Views: 190

Re: Arduino Uno not connecting

Try the hw_connected() function. I dont believe that is for the actual connection of the device !, it is for the ancillary items. JohnF The issue seems to be that you are overloading the receive buffer in AM with constant sending which would not happen in real world use (although I haven't seen you...
by jph
Sun Jun 13, 2021 12:24 pm
Forum: Cockpit building
Topic: Keith 737 mip
Replies: 21
Views: 811

Re: Keith 737 mip

Joe it is a 5.6" 3x4 screen. View area 112x83mm Keith Oooooo ;) :D that bodes well !.. your choice would appear to do the job nicely. :) We need to ensure that once the mode on the display controller is set to HDMI it remains non volatile. - not too much of an issue but preferably you dont want to ...
by jph
Sun Jun 13, 2021 9:37 am
Forum: Arduino
Topic: Arduino Uno not connecting
Replies: 20
Views: 190

Re: Arduino Uno not connecting

Using message port. Arduino sketch I have tried uploading blank sketch, and then run Airmanager still wont connect, but flash arduino and Airmanager connectes, no problem after closing Airmanager and opening it again it connects no problem. but if I load any sketch even a blank one into Uno Airmana...
by jph
Sun Jun 13, 2021 8:46 am
Forum: Cockpit building
Topic: Keith 737 mip
Replies: 21
Views: 811

Re: Keith 737 mip

HI Keith and good morning to you. That is the kind of thing I am talking about yes. Only trouble with that is that the display resolution is 'relatively' low at 640x480 - that is from the spec of the AT056TN53 panel. - but I am also concerned as to the aspect ratio you may require for the 5.6 or 6" ...
by jph
Sat Jun 12, 2021 11:12 am
Forum: Cockpit building
Topic: Keith 737 mip
Replies: 21
Views: 811

Re: Keith 737 mip

I will probably use something like this Joe. http://www.tekswo-display.com/displays/chimei-innolux-at056tn53-v1-inch-tft-lcd-display-panel-touch-screen-module-distributor-datasheet-pdf-arduino.html Keith Hi Brother, Maybe it is better to look for something with an HDMI input ? - the above is a bit ...
by jph
Sat Jun 12, 2021 7:41 am
Forum: Cockpit building
Topic: Keith 737 mip
Replies: 21
Views: 811

Re: Keith 737 mip

Hi, So we are going to have a FV-0834 display for the FV-1070 Control Panel. Keith EDIT: Nha ... The FV-0835 is better as it is a 6" screen in the same real estate. https://ad-aero.com/products/lcd-colour-monitor-2/ Hi brother and a good morning to you :) Are you sure that is what you want ? It is ...
by jph
Fri Jun 11, 2021 11:20 am
Forum: Arduino
Topic: Wiring a real C172 Ignition Switch
Replies: 15
Views: 831

Re: Wiring a real C172 Ignition Switch

You just connect gnd to batt and start to an I/O line. It’s that simple. When not in start the line is pulled high by internal pull-up, when in start position the line is grounded. Remember this is only to tell AM and not for a real application. Pretty sure this is how we helped someone else do thi...