Search found 641 matches

by jph
Sun Jun 13, 2021 12:24 pm
Forum: Cockpit building
Topic: Keith 737 mip
Replies: 21
Views: 710

Re: Keith 737 mip

Joe it is a 5.6" 3x4 screen. View area 112x83mm Keith Oooooo ;) :D that bodes well !.. your choice would appear to do the job nicely. :) We need to ensure that once the mode on the display controller is set to HDMI it remains non volatile. - not too much of an issue but preferably you dont want to ...
by jph
Sun Jun 13, 2021 9:37 am
Forum: Arduino
Topic: Arduino Uno not connecting
Replies: 11
Views: 73

Re: Arduino Uno not connecting

Using message port. Arduino sketch I have tried uploading blank sketch, and then run Airmanager still wont connect, but flash arduino and Airmanager connectes, no problem after closing Airmanager and opening it again it connects no problem. but if I load any sketch even a blank one into Uno Airmana...
by jph
Sun Jun 13, 2021 8:46 am
Forum: Cockpit building
Topic: Keith 737 mip
Replies: 21
Views: 710

Re: Keith 737 mip

HI Keith and good morning to you. That is the kind of thing I am talking about yes. Only trouble with that is that the display resolution is 'relatively' low at 640x480 - that is from the spec of the AT056TN53 panel. - but I am also concerned as to the aspect ratio you may require for the 5.6 or 6" ...
by jph
Sat Jun 12, 2021 11:12 am
Forum: Cockpit building
Topic: Keith 737 mip
Replies: 21
Views: 710

Re: Keith 737 mip

I will probably use something like this Joe. http://www.tekswo-display.com/displays/chimei-innolux-at056tn53-v1-inch-tft-lcd-display-panel-touch-screen-module-distributor-datasheet-pdf-arduino.html Keith Hi Brother, Maybe it is better to look for something with an HDMI input ? - the above is a bit ...
by jph
Sat Jun 12, 2021 7:41 am
Forum: Cockpit building
Topic: Keith 737 mip
Replies: 21
Views: 710

Re: Keith 737 mip

Hi, So we are going to have a FV-0834 display for the FV-1070 Control Panel. Keith EDIT: Nha ... The FV-0835 is better as it is a 6" screen in the same real estate. https://ad-aero.com/products/lcd-colour-monitor-2/ Hi brother and a good morning to you :) Are you sure that is what you want ? It is ...
by jph
Fri Jun 11, 2021 11:20 am
Forum: Arduino
Topic: Wiring a real C172 Ignition Switch
Replies: 15
Views: 814

Re: Wiring a real C172 Ignition Switch

You just connect gnd to batt and start to an I/O line. It’s that simple. When not in start the line is pulled high by internal pull-up, when in start position the line is grounded. Remember this is only to tell AM and not for a real application. Pretty sure this is how we helped someone else do thi...
by jph
Fri Jun 11, 2021 9:57 am
Forum: Arduino
Topic: Wiring a real C172 Ignition Switch
Replies: 15
Views: 814

Re: Wiring a real C172 Ignition Switch

Shouldn’t need to complicate it with power or resistors. I think just using gnd for the commons and utilising the built-in pull-ups for all 3 lines should work out fine. Adding extra external resistors will not harm though. Hi Tony, I originally also thought that - but am thinking more of the start...
by jph
Fri Jun 11, 2021 8:04 am
Forum: Arduino
Topic: Wiring a real C172 Ignition Switch
Replies: 15
Views: 814

Re: Wiring a real C172 Ignition Switch

That standard ignition switch code will not work with a real aircraft ignition switch for the reasons I stated towards the beginning of this thread. You can get it to work but as Ralph said you need to get your head round how the real switch functions. You should be able to make it work with just 3...
by jph
Thu Jun 10, 2021 9:02 am
Forum: Flight Illusion
Topic: Bendix/King Autopilot for X-plane11?
Replies: 6
Views: 115

Re: Bendix/King Autopilot for X-plane11?

If I had one here, and could get, or at least deduce the custom LCD driver requirements (probably quite easy in relative terms looking at the port usage of the original micro and a 'scope where needed ;) ) . Then I would simply rip out all the FI 'dubious' internals and do it from scratch. A Mega or...
by jph
Thu Jun 10, 2021 8:14 am
Forum: General Discussion on Anything
Topic: New EU rules regarding VAT, Mail handling costs, import duty on items from outside the EU from JULY 1st
Replies: 0
Views: 66

New EU rules regarding VAT, Mail handling costs, import duty on items from outside the EU from JULY 1st

Hi guys. Got an interesting text from CTT -the Mail service in Portugal - regarding new EU regulations for items ordered from non EU countries. It comes into force from July 1st. Just wondered if the other EU guys have got the same info ? Basically, at the moment, any item ordered from outside the E...